Installation guide - Self-Adhesive Wall Panels & Mosaic Tiles
Aluxo’s Guide to Installing Self-Adhesive Wall Panels & Mosaic Tiles
Self-adhesive wall panels are the quickest way to give a room a new look. Both Panelux™ Lite and our Mosaic Wall Tiles have a built-in adhesive backing, so on a suitable wall there is no glue, grout, screws or heavy tools needed – just clean, measure, cut, peel and press.
The secret to a long-lasting result is almost entirely down to the wall surface and how firmly you press each panel. This guide covers both.
Which surfaces can self-adhesive panels be applied to?
Any surface that is smooth, dry, clean and sturdy can have panels applied directly. Check your wall against the guide below before you start.
✓ Suitable – apply directly
- Flat painted walls and wood
- Flat concrete walls
- Smooth plaster and drywall
- Ceramic tiles and stone
- Glass
- Metal
✗ Not suitable without treatment
- Sand or stucco textured walls
- Peeling or flaking paint
- Mouldy walls
- Wet or damp walls
- Greasy walls
- Uneven or exposed brick
If your wall has any of the issues above, it must be treated before installation – applying directly will compromise adhesion. Repair, sand, clean or dry the surface first, and we recommend applying extra construction adhesive to the back of each panel for a secure hold.
Equipment needed
Because the adhesive is already on the back, the tool list is short:
- Clean, dry cloth
- Tape measure
- Pencil
- Spirit level
- Sharp utility knife and a straight edge
- Cutting mat or scrap board to cut on
- Gloves (recommended when cutting)
- Tile cutter or metal shears – recommended for the cleanest visible edges on Mosaic Wall Tiles
- Construction adhesive – only for textured, uneven or treated surfaces
Before you start
Unbox your panels and leave them in the room they will be installed in for 48 hours so they can adjust to the room’s temperature and humidity. Keep the protective backing paper on until you are ready to stick each panel.
If you are only covering part of a wall, paint or decorate the surrounding area first – the paint must be fully dry before any panel goes on.
Lay the panels out on the floor before installing. This lets you check the grain or tile pattern and plan the order they go on the wall.
How to install self-adhesive panels in 6 steps
Step 1: Clean the wall
Wipe the surface clean and make sure it is completely dry and dust-free. Dust, grease and moisture are the most common reasons a self-adhesive panel fails to stick.
Step 2: Measure
Decide on your layout and measure the wall. Multiply the width by the height to get the square meterage, then divide by the coverage of one box to see how many boxes you need. Use a spirit level to draw a straight pencil guideline for your first panel – every panel after it follows this line.
Step 3: Cut
Trim panels to fit around corners and obstacles. Score along a straight edge with a sharp utility knife, using several light passes rather than one heavy cut, then snap or finish the cut.
Step 4: Peel & stick
Peel off the protective paper and position the panel against your guideline. Start at one edge and work across – the adhesive grabs quickly, so line it up carefully before pressing it flat.
Step 5: Press firmly
This is the most important step. Press firmly over the entire surface of the panel for at least 3 minutes, paying extra attention to the edges and corners. Even pressure is what activates a strong bond.
Step 6: Finish
Repeat for the remaining panels, then step back and enjoy your new look.
Tips for Panelux™ Lite acoustic panels
- Order enough: each box contains 4 panels (120 x 30cm) covering 1.44m². We recommend ordering at least 2 boxes to complete a feature wall and keep some spares.
- Check the grain: the wood-effect grain pattern and direction are packed randomly and can vary between panels and batches. Lay all panels out first and arrange them before peeling. If you have a preference, please contact us to check stock before ordering.
- Ordering more later? Panels from different batches may vary slightly. If you are a repeat customer, please get in touch before ordering so we can help minimise differences.
- Ceilings: Panelux™ Lite is light enough for ceiling updates, but because gravity works against the adhesive, we recommend adding construction adhesive for extra security overhead.
Tips for Mosaic Wall Tiles
How much material you lose at the joints depends on the tile pattern. Interlocking patterns overlap where one sheet meets the next, while our Square pattern joins edge to edge with no loss. Use the table below when working out how many boxes to order.
| Pattern | Sheet size | Coverage per box | Loss at joints | Order extra |
|---|---|---|---|---|
| Square | 30.5 x 30.5cm | 0.93m² | None – joins edge to edge | 10% |
| Mini Hexagon | 31 x 31cm | 0.93m² | Approx. 0.5cm per sheet | 10–20% |
| Hexagon | 31 x 32cm | 0.9m² | Approx. 1cm per sheet | 10–20% |
| Brick | 31 x 30cm | 0.84m² | Approx. 3cm per sheet | 10–20% |
| Slate (linear) | 36 x 30.5cm | 0.9m² | Approx. 6.5cm per sheet | 15–25% |
Always check the Installation Note on the product page of your chosen tile for its exact figures.
- Create clean edges: with interlocking patterns (Slate, Brick, Hexagon and Mini Hexagon), the end of a run may need to be cut to create a flat, straight edge. Product images show tiles that have already been cut. For visible borders, furniture corners or island ends, a tile cutter or metal shears gives the cleanest finish.
- Not just walls: the sheets can also wrap kitchen islands or upcycle furniture – the same rule applies: smooth, clean, dry and sturdy.
- Sockets and outlets: the tiles are lightweight and easy to trim around switches and sockets. Always switch off the power at the mains before working around electrical fittings.
Cutting around sockets, switches and windows
- Switch off the power and unscrew the socket or switch faceplate.
- Measure from the edge of the last panel and from the floor or skirting board to the fitting.
- Mark the shape on the panel in pencil and cut it out with a utility knife.
- Stick the panel in place, then refit the faceplate over the cut edge for a neat finish.
Frequently asked questions
Do I need glue for self-adhesive wall panels?
No, not on a smooth, clean, dry and sturdy surface. Extra construction adhesive is only needed on textured, uneven or treated walls, and is recommended for ceilings.
Can I stick panels onto textured or stucco walls?
Not directly. The adhesive needs full contact with a flat surface. Either smooth the wall first or apply a strong construction adhesive to the back of each panel.
How long should I press each panel?
Press firmly over the whole panel for at least 3 minutes, focusing on the edges and corners.
Can self-adhesive panels go on tiles or glass?
Yes. Ceramic tiles, stone, glass and metal are all suitable as long as they are clean, dry and free from grease.
How many boxes of Mosaic tiles do I need?
Calculate your wall area, divide it by the coverage of one box (0.84–0.93m² depending on the pattern), then add extra for joints, cuts and waste: 10% for Square tiles, 10–20% for Mini Hexagon, Hexagon and Brick, and 15–25% for Slate.
Do Square mosaic tiles lose any material at the joints?
No. Square mosaic tiles join edge to edge with no overlap. Interlocking patterns lose some material where sheets overlap: around 0.5cm for Mini Hexagon, 1cm for Hexagon, 3cm for Brick and 6.5cm for Slate.
